Altronix AL842ULADA Installation Instructions Manual do Utilizador descarregar pdf (Página 4)

- 4 - AL842ULADA

Output Programming Selection Table:

Outputs must be programmed independently (OUT1 - OUT4)

Function Switch Positions Descriptions

ON OFF

InputtoOutputFollower

Mode

1 2,3 Outputfollowssignalitreceivesfromthecorrespondinginput(i.e.

FACPSyncmodule-maintainssynchronizationof

notificationappliancecircuit).

TemporalCode3Mode 3 1,2 EnablesTemporalCode3signalgenerationoutput.

Thismodewillacceptasteadyorapulsinginput.

SteadyMode 1,2,3 Asteadyoutputsignalwillbegenerated.

Thismodewillacceptsteadyorpulsinginput.

For the above modes Dip Switch 4 determines which Input controls the corresponding output:

Switch 4 in the ON position causes output(s) to be controlled by input 1.

Switch 4 in the OFF position causes output(s) to be controlled by input 2.

Sync Mode Selection Table:

Function

Switch Positions

Descriptions

ON OFF

AmsecoSync

Mode*

1,3,

ThismodeisdesignedtoworkwiththeAmsecoseriesofhorns,strobes,and

horn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,

synchronizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/

strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.

Faraday

SyncMode*

2,4 1,3

ThismodeisdesignedtoworkwiththeFaradayseriesofhorns,strobes,andhorn/

strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchro-

nizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobe

combinationoveratwo-wirecircuitwhileleavingstrobesactive.

Gentex

SyncMode*

Gentexisaregisteredtrademark

ofGentexCorporation.

1,2,

3,4

ThismodeisdesignedtoworkwiththeGentex

seriesofhorns,strobes,andhorn/

strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchro-

nizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobe

combinationoveratwo-wirecircuitwhileleavingstrobesactive.

SystemSensor

SyncMode*

SystemSensorisaregistered

trademarkofHoneywell.

1,2,4 3

ThismodeisdesignedtoworkwiththeSystemSensor

seriesofhorns,strobes,

andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,

synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof

thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.

CooperWheelock

SyncMode*

CooperWheelockisa

registeredtrademarkof

CooperWheelock.

2,3,4 1

ThismodeisdesignedtoworkwiththeCooperWheelockseriesofhorns,strobes,

andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,

synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof

thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.

Note:TheAL842ULADAwillonlysynchronizehorns,horn/strobesandstrobesthatcontainsynchronizationcapability.

Contactsignalmanufacturerformoredetailedinfo.Thesamesynchronizationmodemustbeselectedforalloutputs.

Note: It is required to control visual notification appliances (strobes) via input 1 [IN1] and audible notification

appliances (horns) via input 2 [IN2]. This allows audible notification appliances (horns) to be silenced while

visual notification appliances (strobes) continue to operate.

Amount of Notification Appliances per NAC:

Amseco 27perNAC*

SystemSensor® 32perNAC*

Faraday 39perNAC*

CooperWheelock® 32perNAC*

Gentex® 32perNAC*

*Not to exceed a maximum of 2.5 amp per NAC.

AL842LGK Board

(Output Dip Switches)

INPUT SELECT

TEMPORAL

STROBE SYNC

IN>OUT SYNC

1 2 3 4 5 6 7 8 9 10 11 12

Comentários a estes Manuais

Sem comentários

Altronix AL842ULADA Installation Instructions Manual do Utilizador Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Acessórios para eletricidade Altronix AL842ULADA Installation Instructions