Altronix AL842ULADA Installation Instructions Manual do Utilizador descarregar pdf (Página 3)

AL842ULADA - 3 -

Power Supply Specifications:

AC Input:

120VAC60Hz,5ampsuppliedbyamaximum15ampdedicatedbranchcircuit.

Output:

Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.

One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised

totaloutputcurrentmustnotexceedcurrent8ampinAlarmCondition.

Battery:

Usetwo(2)12VDC/12AHortwo(2)12VDC/7AHbatteriesconnectedinseries.

Stand-by/Alarm Current

Consumption:

90mA/175mA

EOL Resistor (end of line):

2.2K(2200ohm),AltronixModel#AL-EOL22(included).

Ground fault maximum

test impedance:

1000ohm.

Stand-by Specifications:

Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current Aux. Output

24VDC/7AH 24Hours 6.5amp/5minutes ---

24VDC/12AH

(usetwo(2)12VDCbatteriesinseries)

24Hours 6.5amp/5minutes 50mA

24VDC/36AH 24Hours 6.5amp/5minutes 1amp

Note: Unit is equipped with two (2) 1 amp max. auxiliary outputs: “AUX1” will automatically disconnect when

AC is lost. “AUX2” will remain battery backed up during power outage. For loads connected to “AUX2” please,

refer to battery “Stand-by Specifications” above for ratings. When loads are connected to the “AUX1” and or

“AUX2” outputs during alarm condition, the remaining outputs may not exceed 8 amp total alarm current.

(example: AUX1 = 1 amp, AUX2 = 1 amp, outputs up to 7 amp).

Installation Instructions:

WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA72/

ANSI,andwithalllocalcodesandauthoritieshavingjurisdiction.

Productisintendedforindooruseonly.

Carefully review:

Application Guide for AL642ULADA, AL842ULADA, AL1042ULADA

Power Supply Output Specifications (pg. 3)

Stand-by Specifications (pg. 3)

Output Programming Selection Table (pg. 4)

Sync Mode Selection Table (pg. 4)

Terminal Identification Table (pgs. 5-6)

LED Diagnostics (pg. 6)

1.Mounttheunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholesinthe 

 enclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placetheenclosure’s 

 upperkeyholesoverthetwoupperscrews;levelandsecure.Markthepositionofthelowertwoholes.Removethe 

 enclosure.Drillthelowerholesandinstalltwofasteners.Placetheenclosure’supperkeyholesoverthetwoupper 

 screws.Installthetwolowerscrewsandmakesuretotightenallscrews(Enclosure Dimensions, pg. 8).

 Secureenclosuretoearthground(Fig. 1, pg. 3).

2. Connecttheline(L)andneutral(N)terminalstoaseparateunswitchedACcircuit(120VAC,60Hz)

 dedicatedtotheFireAlarmSystem.

3.Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.

4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).

 Usetwo(2)12VDCbatteriesconnectedinseries.

5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]

 anddesiredoutputsignaltype (Output Programming Selection Table, pg. 4).

6. ConnectFACPoutputtothedesiredAL842LGKlogicboardinputs,andnotificationappliancestothedesired 

 AL842LGKlogicboardoutputs(see Application Guide).

Note:The2-wirehorn/strobesyncmodewillonlysynchronizehorns,horn/strobes,strobeswith

 synchronizationcapability.

7. Forconnectionofsmokedetectors,digitaldialer(Optional Hookup Diagram, pg. 7).

Fig. 1

L N

line

ground

neutral

1 2 3 4 5 6 7 8 ... 11 12

Comentários a estes Manuais

Sem comentários

Altronix AL842ULADA Installation Instructions Manual do Utilizador Página 3

Comentários a estes Manuais

Manuais e produtos relacionados com Acessórios para eletricidade Altronix AL842ULADA Installation Instructions