Altronix AL602ULADA Guia de Instalação descarregar pdf (Página 5)

*Note:TheAL602ULADAwillonlysynchronizehorns,horn/strobesandstrobesthatcontainsynchronizationcapability.

Contactsignalmanufacturerformoredetailedinfo(see Appendix A.4, pg. 12).Thesamesynchronizationmodemustbe

selectedforalloutputs

Amount of Notification Appliances per NAC:

Amseco 27perNAC*

SystemSensor® 32perNAC*

Faraday 39perNAC*

CooperWheelock® 32perNAC*

Gentex® 32perNAC*

*Not to exceed a maximum of 2.5 amp per NAC.

Terminal Identification Table:

AL800LGK9E Logic Board

Terminal

Legend

Function/Description

IN1+,IN1-

IN2+,IN2-

(Supervised)

Theseterminalsconnecttothe24VDCFACPnotificationappliancecircuitoutputs. 

(ClassA,StyleZorClassB,StyleW,X,Y)Inputtriggervoltageis8-33VDC@5mAmin.

Terminalpolarityisshowninalarmcondition.Duringanalarmconditiontheseinputswillcause

theselectedoutputschosentodrivenotificationappliances.Thedesignatedoutputsaresetbyoutput

switches[OUT1throughOUT4](Output Programming Selection Table, pg. 4). Atroubleconditionon

anoutputloopwillcausethecorrespondinginputtotriptheFACPbyopeningtheFACPloop.An

alarmconditionwillalwaysoverridetroubletodrivenotificationappliances.

RET1+,RET1-

RET2+,RET2-

(Supervised)

For(ClassA,StyleZhookupstheseterminalpairsreturntoFACPNAC1and/orNAC2.For

ClassB,StyleW,X,YhookupstheFACPEOLresistorfromtheNAC1and/orNAC2outputsare

terminatedattheseterminals.

C“DRY1”NC

C“DRY2”NC

(Dryinputtrigger)

Anopenacrosstheseinputs,willcausetheselectedoutputschosentodrivenotificationappli-

ances.Thedesignatedoutputsaresetbyoutputswitches[OUT1throughOUT4](Output

Programming Selection Table, pg. 4).Notetheseinputsareunidirectionalandwillnotreporta

troubleconditiontotheFACP.

+OUT1-- 

+OUT2--

+OUT3-- 

+OUT4-- 

(Supervised)

Notificationappliancesareconnectedtotheseregulatedoutputs (see 02 Application Guide pg.

2-4). Eachpower-limitedoutputwillsupply2.5amp.Two(2)outputsmaybeconnectedinparallel

foramaximumNACoutputcapabilityof4amp.Totalsupplycurrentis6.5amp(see note below).

Outputsarecontrolledbydesignatedinput1[IN1]orinput2[IN2](Output Programming Selection

C“FAULT”NC

(Common

troubleinput)

Anopencircuitacrossthispairofterminalswillcause[IN1andIN2]tosimultaneouslysignala

troubleconditionbacktotheFACP(TypicallyusedtoreportACorBATFail).(form“C”contact

1amp/28VDC)(Fig. 2, pg. 7).

NC,C,NO

(Common

troubleoutput)

Thesearedrycontacttroubleoutputsthatfollowanygeneralloop/systemtroubleconditions.

(Typicallyusedtotriggeradigitalcommunicatororotherreportingdevice).

(form“C”contact1amp/28VDC0.35PowerFactor)(Fig. 2, pg. 7) .

 --AUX+ Thisseparate1ampmaxauxiliarySpecialApplicationPoweroutputcircuitistypicallyusedto 

power4-wiresmokedetectors.Seeattachedlistofdevices(Appendix A, pgs. 10-12).

+DC--  24VDCfrompowersupply.

Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power

outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” pg. 3 for ratings. When

loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 6.5 amp

total alarm current (example: AUX = 1 amp, outputs up to 5.5 amp).

AL602ULADA - 5 -

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentários a estes Manuais

Sem comentários

Altronix AL602ULADA Guia de Instalação Página 5

Comentários a estes Manuais